Me 410 gunsight issues....

[Rommel1717]

So I am having an issue with being able to see the reticle in all the different gunsights in the Me410.

 

The reticle is too low I can't get a good sight picture in them. 

 

It's like I am sitting to low in the seat, the reticle is there but I have to try to prop myself or my head up to see the reticle. 

 

I am using track IR but I checked all the other gunsights and everything is working fine in all other aircraft including in all turrets as well as the rear gun in the 410. 

 

When I hit the default Numpad 5 to reset the gunsight it doesn't reset like in other aircraft.  

 

The only issue I'm having is with the 410. 

 

Any help would be appreciated. 

[LukeFF]

It's explained in the manual how you can adjust your head position. 

[Rommel1717]

Can you post a copy of where it says that in the manual because I can't find it...

 

and I find it strange that the 410 is the only plane I am having this issue with. 

 

Cheers. 

[SCG_Tzigy]

15 minutes ago, Motivated said:

I believe Page Up, Page Down, Home, and End are the keys you're looking for. Don't forget to press F10 to save your changes.

pause IR 1st, then adjust; 410 is special b/c the different sights

[Rommel1717]

Ok I know the head up(page up)and head down(page down) does not work while running Track IR, I will try adjusting while not running track IR and will let you know how it goes....  

SO with Track IR not running the page up and page down keys work but when I hit F10 nothing seems to happen at least there is no message and when I hot F5 it reverts to the old view. When I finish the mission and jump back in the view where I cannot see the reticle is still there so no change not sure what is going on and how I can fix this. Why does this happen only in the 410? 

[Rommel1717]

So here is what I have found:

- The default loadout gunsight and the 2xMG131(ME410B) loadout gunsight works fine I have no issues. 

- The C12D and Revi16B gunsights are not working the reticle is far too low.

I can pause Track IR use page up and center the reticle. As soon as I unpause Track IR it reverts to the old view. I have hit F10 after centering the view in the gunsight but it doesn't seem to do anything. 

If I want to use the sight I would have to fight and fly with Track IR paused which is difficult to do. As I mentioned as soon as I unpause Track IR it reverts to the old view where the reticle is too low and you can't see it.

- The ZFR4 sight is usable but not perfect it, the reticle is higher than the C12D and the Revi16B gunsight but could be adjusted up a little. It also works fine in the zoomed in Shift-V mode.

 

Hopefully this can be fixed in a patch or if I am doing something wrong with my Track IR or my F10 key isn't binded, I am not sure what the issue is. Anymore suggestions or tips would be appreciated.  

Edited September 12, 2022 by ACG_Rommel

[SCG_Tzigy]

F10 is not saving your view. You might need to look into commands and re-bind

 

1. Pause IR

2. Adjust views

3. Hit F-10 (save view) or whatever u asigned

4. Unpause IR

5. Center view command should should default to the new view

Edited September 12, 2022 by SCG_Tzigy

[Rommel1717]

Got it to work, it was because I didn't have the save view key binded. So have it saved to F10 and all is good now. 

 

Thank you so much for the help.

Cheers!